Simple cosplay cat ears made out of Fosshape, decorated with rhinestones and complete with RGB LEDs for color changing effect. Materials: Fosshape 300 2 x slow scroll RGB LEDs 2 x CR2032 coin cell batteries 2 x coin cell battery holders 100 flatback rhinestones 2 x hairclips fake fur steel ball chain Tools: scissors heat […]
Project: APA102-2020 MicroNova Custom LE...
Solar botics
February 23, 2018
I created this choker as a project to demonstrate the new MicroNova APA102-2020 LED strips.
Photo by Yeti, edited by Batgirl
These addressable LEDs are extremely small, less than 1/4 the size of a standard 5050 LED.
This project was built using engineering sample standard MicroNova 99 LED / meter strips . The MicroNova strips we are selling have 198/meter - twice the density!
Reason for a Choker necklace:
Hats have been done, shoes have been done, pendants have been done.
This is something new for a Valentine’s dance costume, so I decided to go with a choker design. I also wanted something that was interactive, something that would add another layer of WOW to just lighting.
Build:
I used a Wemos D1 Mini development board along with a boost-converting battery shield for the Wemos D1.
The battery shield was a particularly good choice here because the MicroNova LEDs should be supplied a solid 5VDC. This board boosts the battery voltage to 5V, and then the Wemos D1 Mini bucks it down to 3V3 for it's own operation.
A mini SPDT Slide switch toggles the power from the battery shield to the D1. This allows charging the battery using the battery shield USB connector while not powering the D1.
Epoxy locks the switch and wires in place.
The battery used is a conveniently handy older 450mAh Lithium Polymer. Depending on the lighting mode, this battery can power the necklace for a couple of hours.
I used elastic thread to attach the LED strip and components to the necklace. A heavy duty needle was all that was needed to punch through the (imitation) leather belt. Because the thread was elastic and tied under tension, it held the MicroNova strip well in place.
Operation:
When the choker powers up, it creates a WiFi Access Point called "HeartBurnChoker1".
Once I connected to this WiFi, I opened a browser and went to 192.168.4.1. The control interface is simple, but effective. The D1 Mini has more than ample power and speed to effectively drive these LEDs. The MicroNova features separate clock & data lines, so even relatively slow I/O (like Raspberry Pi) can still make it work.
MORE POSTS
Dave's Office...
Dave, el Presidente of Solarbotics and HVW Tech, may be difficult to get a hold of due to an inability to get into his office! So if you call and ask for Dave you'll have to wait while we dig him out. And if you are waiting for Dave check out this very cool Star […]
Merging Solarbotics & HVW Inventori...
So... We've finally decided to go all-out and bring over all the inventory from HVW Tech and integrate it into Solarbotics. This is a pretty big undertaking, and as such you're going to need to tip toe around the construction tape and sawdust while we re-arrange everything. How will this effect you? First off, we're […]
GM15 Nano Robot Sumo
We've had some requests about our own demo Nano robot sumo "BittyBad", which uses a pair of GM15 gear motors. On the GM15 detail page, you'll see a picture of it! It features 2 GM15 gear motors, two 90mA/h LiPoly 3.7V batteries (in series), two "ProxDots" objects sensors, a pair of edge-sensors and a (gasp!) […]
Solarbotics has been operating for more than 25 years, bringing electronics know-how and supplies to both the electronics professional and hobbyist. We'll be happy to help you too!
Solarbotics, Ltd. is not responsible for misprints or errors on product prices or information. For more information, please see our Terms and Conditions.
Warning: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Please visit www.P65Warnings.ca.gov for more information. This item was manufactured prior to August 31, 2018.