Strange set of Atmel '328 ICs...

Dave Hrynkiw
August 26, 2010

Unlike Sparkfun, who actually manage to find fake Atmel ICs, we just get strange batches.

The Atmel ATMega328 is the power behind the Arduino/Freeduino/*duino, and we have to set up a programming system to burn the venerable Arduino Bootloader into these chips.

We normally use an AVR STK500 in HVSP (high voltage serial programming) mode, as that lets us be absolutely sure the fuses are set correctly and the burn is correct. Interestingly enough, this last batch of chips refused to work with our batch files. Asking the chip's ID often returned 0x01 0x03 0X05 instead of the expected signature.

After spending a day checking to see if the programmer was broken (nope) or if the chips were fake (nope, we think), we did find that they did respond to regular old ICSP (in-circuit serial programming), but only partially.

Digging around, we found some older ATMega328 chips that worked fine, and compared them to this new batch. This troublesome batch has a date code of 1015 (15th week of 2010), and a batch code on the bottom as 9J4302 / 35473d / 1-P1015 e3.

So we re-wrote our batch file burning code to use AVRDude instead of the STK500 command-programmer, and to run it in ICSP mode on the STK500. The key addition is the "-B" part, which slows down the communication a bit. You want it as low as possible for fastest burn times. I tried a "-B 2" on both fuse & programming lines, but that really slowed the process. What's below is what we settled on.

: Set fuse bits, lock bits, voltages
.avrdude -c stk500v2 -i 20 -p m328p -P COM1 -b 115200 -B 1.8 -e -u -U lock:w:0x3f:m -U efuse:w:0x05:m -U hfuse:w:0xDA:m -U lfuse:w:0xFF:m
: Burn & Lock Arduino hex bootloader file
.avrdude -c stk500v2 -p m328p -P COM1 -b 115200 -B 1.1 -U flash:w:%HEXFILE% -U lock:w:0x0f:m

Hope that'll save anybody else from blowing better part of a day figuring out why their Atmel isn't programming normally!

MORE POSTS

May 19, 2011
We're CLOSED for Maker Faire

Yeah, we warned you. We're not even in our office to write out this newspost. Nay, this is one of them fancy pre-recorded messages. It may or may not self destruct. So, yes, we're closed from May 19th (Thursday) to the 24th  (Tuesday). We'll resume filling/shipping orders and replying to any correspondance once we're back […]

September 10, 2013
Calgary Mini Maker Faire Ticket Giveaway...

We've got two pairs of weekend passes for the Calgary Mini Maker Faire taking place this weekend up for grabs. To enter, send an email to it@solarbotics.com with the subject of "I <3 Solarbotics" to enter. Two winners will be selected Friday the 13th @ Noon.

April 16, 2014
Wednesday Links: Helical Springs, Electr...

Did you see the lunar eclipse on Monday night? I wish they had it rescheduled for Sunday afternoon, so all of us night-owls-who-have-to-get-up-early could watch that. But noooOOoOO. But at least the internet will save us. At least from information deficit. Laser Cut Helical Springs I wonder if zigzag helical springs can still travel down […]

August 6, 2011
Epilog Laser Problems/Solutions, New Pro...

This week, we've had a lot of fun with our Epilog Laser. And by fun, I obviously mean "turmoil and general miserableness". Fortunately, we've sorted the issue out. What I'm going to do is chronicle our pains, describing the exact issue and solution, so that The Googles will index the knowledge for other explorers of […]

Solarbotics Ltd Logo
Solarbotics has been operating for more than 25 years, bringing electronics know-how and supplies to both the electronics professional and hobbyist. We'll be happy to help you too!

Solarbotics, Ltd. is not responsible for misprints or errors on product prices or information. For more information, please see our Terms and Conditions.

Warning: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Please visit www.P65Warnings.ca.gov for more information. This item was manufactured prior to August 31, 2018.