Grant has taken some time to document how to turn a standard 81:1 GM10 pager gear motor and turn it into a 9:1 version. Why would you want to do that? You tell me - I'd love to know what project you build with a speed demon like that! Read More...
Unlike Sparkfun, who actually manage to find fake Atmel ICs, we just get strange batches.
The Atmel ATMega328 is the power behind the Arduino/Freeduino/*duino, and we have to set up a programming system to burn the venerable Arduino Bootloader into these chips.
We normally use an AVR STK500 in HVSP (high voltage serial programming) mode, as that lets us be absolutely sure the fuses are set correctly and the burn is correct. Interestingly enough, this last batch of chips refused to work with our batch files. Asking the chip's ID often returned 0x01 0x03 0X05 instead of the expected signature.
After spending a day checking to see if the programmer was broken (nope) or if the chips were fake (nope, we think), we did find that they did respond to regular old ICSP (in-circuit serial programming), but only partially.
Digging around, we found some older ATMega328 chips that worked fine, and compared them to this new batch. This troublesome batch has a date code of 1015 (15th week of 2010), and a batch code on the bottom as 9J4302 / 35473d / 1-P1015 e3.
So we re-wrote our batch file burning code to use AVRDude instead of the STK500 command-programmer, and to run it in ICSP mode on the STK500. The key addition is the "-B" part, which slows down the communication a bit. You want it as low as possible for fastest burn times. I tried a "-B 2" on both fuse & programming lines, but that really slowed the process. What's below is what we settled on.
: Set fuse bits, lock bits, voltages
.avrdude -c stk500v2 -i 20 -p m328p -P COM1 -b 115200 -B 1.8 -e -u -U lock:w:0x3f:m -U efuse:w:0x05:m -U hfuse:w:0xDA:m -U lfuse:w:0xFF:m
: Burn & Lock Arduino hex bootloader file
.avrdude -c stk500v2 -p m328p -P COM1 -b 115200 -B 1.1 -U flash:w:%HEXFILE% -U lock:w:0x0f:m
Hope that'll save anybody else from blowing better part of a day figuring out why their Atmel isn't programming normally!
Grant has taken some time to document how to turn a standard 81:1 GM10 pager gear motor and turn it into a 9:1 version. Why would you want to do that? You tell me - I'd love to know what project you build with a speed demon like that! Read More...
Hi all. It's Monday, May 19th, and for some reason, we have something called "Victoria Day" today. We're not open today, but I promise, we'll be back in tomorrow, rested and relaxed and ready to process your orders! Now to just beat these darn springtime allergies...sniiiiifffff....
The America Solar Challenge finishes here in Calgary tomorrow (July 27) betweein 11 and 3:30pm! The teams are coming up over McKnight Blvd., which isn't far from our offices. We'll be out watching them go by for a few hours tomorrow, so if the phones don't get answered for a bit, you'll know why. Go […]
I wonder what's going to happen if you stuff all the dry beer ingredients in your mouth? Would you turn into a foam spitting monster, a rabid-looking human? Read along, and you'll know what I'm talking about: Glassified: Augmenting a traditional ruler with digital functionality I am past needing this for school, but I sure […]
Solarbotics, Ltd. is not responsible for misprints or errors on product prices or information. For more information, please see our Terms and Conditions.
Warning: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Please visit www.P65Warnings.ca.gov for more information. This item was manufactured prior to August 31, 2018.