I2C 12-Bit, 8-CH Analog-To-Digital Converter


This Product Has Been Discountinued, This Page Is For Reference Only.



$19.99 ea.
$19.99 ea.

The I2C-ADC board is an I2C 12-bit, 8-CH Analog-to-Digital Converter module. The module can be configured as a Single-Ended Inputs Mode or Differential Inputs Mode.

Description [Hide]

The I2C-ADC board is an I2C 12-bit, 8-CH Analog-to-Digital Converter module. The module can be configured as a Single-Ended Inputs Mode or Differential Inputs Mode. There are no external components required. Only two signal lines SDA and SCL plus supply voltage and ground are required to be connected. This makes it perfect for embedded systems that require more input/output ports.

This board features innovations that set it apart from other ADC module. Innovations feature like on-board I2C address jumpers, pull-up resistors, power LED and 2.5V reference. The module can be quickly connected directly on to the breadboard. The board is small and compact in size 0.70 x 0.70 inches.

The I2C-ADC is designed base on ADS7828 IC. It is a single-supply, low-power, 12-bit data acquisition device that features a serial I2C interface and an 8-channel multiplexer. The Analog-to-Digital (A/D) converter features a sample-and-hold amplifier and internal, asynchronous clock. The combination of an I2C serial, 2-wire interface and micropower consumption makes the I2C-ADC ideal for applications requiring the A/D converter to be close to the input source in remote locations and for applications requiring isolation.

Two jumper pins vary the fixed I2C address and allow up to four devices to share the same I2C bus. That is total of 32 channels.


• Stand alone module, no external components required
• On-board I2C address jumpers, pull-up resistors, power LED and 2.5V reference
• Decoupling supply voltage
• Design easy for breadboard
• High quality double sided PCB
• All SMT components
• Small and compact in size 0.70 x 0.70 inches
• Dual row 0.6” width, 0.1” pitch header pins
• Operating power supply voltage range of 2.7V to 5V
• Suitable for 3.3V or 5.0V microcontroller
• 8-Channel multiplexer
• 50kHz sampling rate
• Internal 2.5V reference
• I2C interface supports: Standard, Fast and High-Speed Modes

Documentation [Hide]

You Might Also Like [Hide]


6-Pin Shield Stacking Header

Want to stack more than one shield at a time? Use these instead of standard 6-pin headers to add extra functionality to your shield!

$0.45 USD


RS-232 Driver Module - DCE

The DTE RS-232 module is a tight and tidy way to convert RS-232 (computer-level) signals down to a microcontroller level signal strengths. DCE means it's configured as a "Data Communications Equipment" (with 9 holes).

$11.95 USD


Logic Level Converter

The SparkFun logic level converter is a small device that safely steps down 5V signals to 3.3V and steps up 3.3V to 5V. This level converter also works with 2.8V and 1.8V devices.

$1.95 USD


EFX-Tek RS-485 Adapter

The EFX-Tek RS-485 adapter is an ideal solution for putting multiple microcontrollers on a custom network.

$31.46 USD


XBee-PRO Module - 60mW Wire Antenna

The low-power XBee 802.15.4 and extended-range XBee-PRO 802.15.4 use the IEEE 802.15.4 networking protocol for fast point-to-multipoint or peer-to-peer networking.

$38.45 USD


3-Panel Breadboard

This 3-Panel Breadboard is a great prototyping tool that offers a large workspace.

$19.95 USD


Single Panel Breadboard

This breadboard is high quality and features nickel plated contacts in order to insure very low clip resistance and durability in order to insure that the board will work for years to come.

$4.95 USD


Parallax USB to Serial RS-232 Adapter

The Parallax USB to RS-232 is a great little adapter that takes your mini-USB connector and converts it to a RS-232 interface!

$14.95 USD


Synapse RF300PD1 with SMA Connector

A module that runs at OTA (Over-The-Air) speeds up to 150Kbps and has a maximum transmission range of 3 miles! Perfect for when you need a separate frequency band when already using 2.4GHz nodes in an application. Just apply power and you've connected a mesh network.

$38.60 USD


16MHz Through-Hole Crystal for Arduino

16.000MHz. That's pretty darn precise. And exactly the value needed to run an ATmega8/168/328 microcontroller at Arduino-compatible frequency!

$0.95 USD





Remember Me

Forgot Your Password?

Don't Have an Account?
Sign Up!