Shooting analog pictures, shooting bullets underwater, shooting… theremin noises from goggles, shooting… human-powered helicopters! if that doesn’t make any sense, see the links below: Steampunk theremin goggles A wicked build by [Sarah] - theremin steampunk goggles. Photo sensor will feel the amount of light and the slider would adjust the pitch of the sound produced. Check […]
New Product: OPEN BEAM! (..and some othe...
Dave Hrynkiw
August 24, 2012
We have a pretty darn big announcement for you today: we're now distributing Open Beam! It's a new handy-dandy construction system that got its start from Kickstarter, and is gaining a lot of immediate support. Right now, we're stocking all the items except for the kits, which we'll probably bring onboard in the near future. We've put all our stock into a convenient Open Beam Category, but you can also see all of the new stock here:
|
OpenBeam Extrusion - 1000mm Length $10.00 (Silver), $12.00 (Black) This is the 'beam' part of 'Open Beam'. This is the central building component for the system, and is available in both black and silver. |
 |
OpenBeam T Joining Plate - 2 Pack $1.90 T-shaped joining plates for all your OpenBeam creations! |
 |
OpenBeam L Joining Plate - 2 Pack $1.90 L-shaped joining plates for all your OpenBeam creations! This one handily supports 45 & 90 angles. |
 |
OpenBeam Servo Bracket $7.50 OpenBeam's servo bracket allows you to use just about any standard size servo with your OpenBeam or MicroRAX projects. |
 |
OpenBeam NEMA17 Stepper Motor Bracket $7.50 NEMA17 Stepper Motor Mounts for the OpenBeam construction system. |
 |
OpenBeam 608 Bearing to NEMA17 Adapter $4.00 OpenBeam's adapter to use a 608 skate bearing with NEMA17 mounts. |
 |
OpenBeam Shaft Clamp Kit $8.00 The OpenBeam Shaft Clamp Kit allows you to clamp shafts anywhere on your OpenBeam project. |
 |
OpenBeam Feet - 2 Pack $1.90 Feet to fit OpenBeam extrusions, keep your desk scratch free! |
 |
OpenBeam M3 Nuts - 100 Pack $3.00 100 pack of M3 nuts for use with OpenBeam. |
 |
OpenBeam Button Head Socket Cap Screw - 100 Pack $7.00 100 pack of button head socket cap screws for use with OpenBeam. |
 |
OpenBeam 2mm Flat bottom Hex Driver $4.00 2mm flat bottom hex driver for use with OpenBeam. |
 |
OpenBeam 2mm Ball-End Hex Driver $5.50 2mm ball tip hex driver for use with OpenBeam. |
 |
OpenBeam 5.5mm Hex Nut Driver $9.00 5.5mm hex nut driver for use with the OpenBeam system. |
 |
OpenBeam 2mm Hex Key $1.80 2mm Hex key for use with the OpenBeam system. |
But wait, THAT'S NOT ALL! We also have a few other items that we brought in this week, and we'd like to show 'em off so they don't get left behind in the cold.
 |
PICAXE-28X2 Shield Base (Assembled) $24.00 The PICAXE-28X2 shield base has been designed to be compatible with almost all 'shield modules' as used with the Arduino system. This a very affordable project board for PICAXE development! |
 |
Synapse RF266PC1 - XBee Footprint, with Chip Antenna $32.95 Want to try Synapse, but only have XBee hardware? HAH - Synapse thought of that with their new RF266PC1. Synapse power in an XBee footprint! |
 |
Synapse RF200PF1 with F-type Antenna $29.00 XBee is good; Synapse is just better. More I/O, embedded python, and generally better range at comparable cost! This particular module is 2.4GHz with OTA (Over-The-Air) speeds up to 2Mbps, maximum 2.5miles (~4km) range and a F-type PCB for compact installation. |
Well folks, that's all we gots. Go forth, drool over the fancy new Open Beam goodness, and above all else, enjoy the last wonderful weekend of August.
MORE POSTS
Dave's Office...
Dave, el Presidente of Solarbotics and HVW Tech, may be difficult to get a hold of due to an inability to get into his office! So if you call and ask for Dave you'll have to wait while we dig him out. And if you are waiting for Dave check out this very cool Star […]
Holiday Hours and Shipping
This is a quick note to announce our holiday schedule, which is going to be as follows: December 24 (Christmas Eve)- 9am to 12pm (half day) December 25 (Christmas Day) - offices are closed December 26 (Boxing Day) - offices are closed December 31 (The Day Before New Year's Day) - 9am to 12pm (half […]
SCC3733 Solarcell hacking
Here's a tip submitted by Rick Steenblik regarding hacking our SCC3733 for less voltage, but more current: After using your SCC3733 solar cells for a couple of bots I noticed that they can be altered to provide about 3.3v at 80ma (in full sun) by cutting the bus connector on the back to electrically separate […]
Solarbotics has been operating for more than 25 years, bringing electronics know-how and supplies to both the electronics professional and hobbyist. We'll be happy to help you too!
Solarbotics, Ltd. is not responsible for misprints or errors on product prices or information. For more information, please see our Terms and Conditions.
Warning: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Please visit www.P65Warnings.ca.gov for more information. This item was manufactured prior to August 31, 2018.