Well, it's the end of another week, and - Hey! I have something that you might actually be interested in. We've just received some PICAXE inventory, particularly the PICAXE-28 Project Board. So that's now available and ready for us to throw into a box (not literally, of course) and send in your direction. And now that […]
DIY LED Fosshape Horns
Solar botics
November 17, 2016
A handy tutorial explaining how to put together the RGB LED Horns. Make your own, or get a kit with everything included (except for the paint).
Supplies:
Fosshape 300
2 x slow scroll RGB LED
2 x coin cell batteries
conductive thread
2 x coin cell battery holder - sewable
2 x pieces of velcro (hook side)
dimensional fabric paint (like this) - not included in the kit
Tools:
scissors
needle
heat gun
needlenose pliers
clear nail polish - optional
Step 1. Pattern
Cut out your own pattern - a simple triangle and a circle for the base.
Step 2. Shape the horn
Sew the triangle along the long edge. Shrink and form it over the heat gun - make sure to watch the fabric, when heated too much it will melt and form holes. Instead of trying to form the hot Fosshape with your hands, the best way to harden the shape is to hold it above the heat gun making sure to heat it evenly and let it shrink. Shrink the bases too while keeping them flat, but don't sew them on yet.
Step 3. LEDs preparation
With needlenose pliers curl up the LED legs and bend them 90 degrees so that the loops sit flat when the LED is facing up.
Step 4. Battery holder
Grab the battery holder, a coin cell and the base and attach the LED using conductive thread. Make sure the polarity of LED and battery are correct. If everything is wired right the LED will light up.
Step 5. Sew the base
Sew the base to the horn like shown and add a little tab of Fosshape and Velcro to the opposite side in order to keep it in place. Paint some clear nail polish on the bottom of the horns to isolate the conductive thread from touching the metal of the hair clip. Alternatively, you can fluff up the small scraps of Fosshape and fuse them over the stitches to protect the conductive thread.
Step 6. Paint
Embellish the horns with a pattern of your choice using the Tulip paint. It will take about 4 hours to dry. The Fosshape disperses the light quite nicely.
Step 7. Hair clip
Hot glue the hair clips to the bottom of each horn. Alternatively, you can sew the finished horns to hair clips or a head band.
MORE POSTS
LMR Start Here Kit, Beetlebot Preorders
Good news! Despite a few small setbacks and stumbling blocks, we've survived both the office move and Maker Faire! (I was going to say that at least nothing burned down, but that isn't exactly the case...). But now that things are settling back to normal, we'll be doing our best to bring you more awesome […]
New Product: Sensors
Seeed Grove - IMU 9DOF V2 $18.23 The Grove 9 degree-of-freedom (DOF) module features the MPU-9250, and is an easy-to-use all in one module from SeeedStudios. Teensy Prop Shield LC $13.00 The Prop Shield LC is the stripped-down version of the Teensy Prop Sensor Shield (motion sensors removed) Prop Shield With Motion Sensors $27.00 The […]
Austin Maker Faire 2008
It's that wonderful time of year when you can see your breath in the air while you wait at the bus stop. Frost decorates the blades of grass, motorists spend five minutes scraping ice off the windshield before departing and there are hints of snow when you look up at the hills. So what's a […]
Solarbotics has been operating for more than 25 years, bringing electronics know-how and supplies to both the electronics professional and hobbyist. We'll be happy to help you too!
Solarbotics, Ltd. is not responsible for misprints or errors on product prices or information. For more information, please see our Terms and Conditions.
Warning: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Please visit www.P65Warnings.ca.gov for more information. This item was manufactured prior to August 31, 2018.