The instructions for assembling the Pi v3 and the previous acrylic Pi SAFE are quite similar. The only difference between the models is the location of the LED light pipes, so these Pi3 instructions apply generally to all Pi SAFE versions.
1. Your Parts!
Step 1: Parts
8 x 4-40 nuts
8 x 4-40 x 3/8" bolts
2 x Clear acrylic light-pipes
4 x Black acrylic spacers
6 x Black acrylic SAFE sides (shown here with brown protective paper already removed)
0 x Raspberry Pi (sorry - not included in the kit!)
2. The Baseplate
Step 2: Baseplate preparation
Find 4 of the 4-40 x 3/8" bolts, and put them through the baseplate, and press the spacers on from the other side. Thee bolts will sort of stay put until you can get the Raspberry Pi on the baseplate. (If adding to a VESA mount, do only 2 diagonal screws)
3. Adding the Raspberry Pi
Step 3: Mounting the Pi to the baseplate
Slide the Raspberry Pi onto the bolts. The Pi is designed for metric M3 hardware, but we're still using imperial #4 hardware, which is a smidge bigger. The bolts may need to be screwed through the holes in the Pi.
Add the #4 nuts, and tighten them down.
4. Adding 3 of the 4 Sides
Step 4: 3 of the 4 sides to be added to the baseplate
Arrange the sides as shows. The sideplate on the top in this image has the long cutout to accommodate a ribbon cable from the 40-pin expansion port. The front faceplate on the right (with the label engravings face-down) is for the communications side. The sideplate on the bottom has the ports for the power, video, and audio I/O.
Align them all up on the baseplate, and use a pair of 4-40 nuts and bolts to lock them in place.
5. Adding the SD-Card / LightPipe Faceplate
Step 5a: Preparing for lightpipes
Lay the final side faceplate face-down beside the assembly, and pop the clear lightpipe parts out of their holder. It is not necessary to strip the paper off this part.
Sandwich the two lightpipes together, and push them into the lightpipe indicator hole. They will sit a bit loose until the faceplate is attached to the baseplate.
Step 5b: Lightpipe assembly
Carefully assemble this assembly to the baseplate, and finish attaching it with the remaining 4-40 nuts and bolts.
Step 6: Top Plate mounting
Notch the top plate into the slots in the rear faceplate, and gently flex the frontplate out to let the tab snap into place. You're ready to power up, with full access to the indication LEDs on the Pi mainboard via the lightpipes!
Well, that certainly was weird. Our telephone lines were having some problems earlier this afternoon, and some people were unable to get through. We would like to apologize and get this ironed out as soon as possible. If you can not connect during our business hours (0900 - 1800 MST), please leave us a message […]
Well, it appears that some people around the office are a bit grumpy after having to come back from their nice long winter hibernation. But it's the New Year! Time to feel awesome and optimistic and bubbly about the upcoming year full of possibilities. That's okay though, they just need to be injected with a […]
Here's a great booklet to accompany any new Freeduino purchase - "Getting Started with Arduino", written by Massimo Banzi (the co-founder of the Arduino Project). This title is based on his free-download introduction PDF, but takes is much farther, guiding new electronics enthusiasts into how to use the Arduino / Freeduino in a project. Also […]
Solarbotics has been operating for more than 25 years, bringing electronics know-how and supplies to both the electronics professional and hobbyist. We'll be happy to help you too!
Solarbotics, Ltd. is not responsible for misprints or errors on product prices or information. For more information, please see our Terms and Conditions.
Warning: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Please visit www.P65Warnings.ca.gov for more information. This item was manufactured prior to August 31, 2018.