The instructions for assembling the Pi v3 and the previous acrylic Pi SAFE are quite similar. The only difference between the models is the location of the LED light pipes, so these Pi3 instructions apply generally to all Pi SAFE versions.
1. Your Parts!
8 x 4-40 nuts
8 x 4-40 x 3/8" bolts
2 x Clear acrylic light-pipes
4 x Black acrylic spacers
6 x Black acrylic SAFE sides (shown here with brown protective paper already removed)
0 x Raspberry Pi (sorry - not included in the kit!)
2. The Baseplate
Find 4 of the 4-40 x 3/8" bolts, and put them through the baseplate, and press the spacers on from the other side. Thee bolts will sort of stay put until you can get the Raspberry Pi on the baseplate. (If adding to a VESA mount, do only 2 diagonal screws)
3. Adding the Raspberry Pi
Slide the Raspberry Pi onto the bolts. The Pi is designed for metric M3 hardware, but we're still using imperial #4 hardware, which is a smidge bigger. The bolts may need to be screwed through the holes in the Pi.
Add the #4 nuts, and tighten them down.
4. Adding 3 of the 4 Sides
Arrange the sides as shows. The sideplate on the top in this image has the long cutout to accommodate a ribbon cable from the 40-pin expansion port. The front faceplate on the right (with the label engravings face-down) is for the communications side. The sideplate on the bottom has the ports for the power, video, and audio I/O.
Align them all up on the baseplate, and use a pair of 4-40 nuts and bolts to lock them in place.
5. Adding the SD-Card / LightPipe Faceplate
Lay the final side faceplate face-down beside the assembly, and pop the clear lightpipe parts out of their holder. It is not necessary to strip the paper off this part.
Sandwich the two lightpipes together, and push them into the lightpipe indicator hole. They will sit a bit loose until the faceplate is attached to the baseplate.
Carefully assemble this assembly to the baseplate, and finish attaching it with the remaining 4-40 nuts and bolts.
Step 6: Top Plate mounting
Notch the top plate into the slots in the rear faceplate, and gently flex the frontplate out to let the tab snap into place. You're ready to power up, with full access to the indication LEDs on the Pi mainboard via the lightpipes!
This is just a subtle reminder that Solarbotics & HVW Technologies will both be closed January 1st and 2nd (Thursday and Friday), while we're out fighting raging hangovers being productive members of society. We hope 2008 treated all of you well and that 2009 will be even better. And if it isn't, well... Once we […]
Hi all. For all you Sumovore-owners, just a note to let you know that the new Atmel-WinAVR code is online (Atmel brainboard page under resources). Just some tweaks to make it compatible with the latest versions of WinAVR. Also, Dan Peirce has ported the JAL portion of the '877 brains to the Hi-Tech PICCLite compiler, […]
Ummm, yup! Here's an April Fool's joke for you - that April Fool's wasn't a joke! Solarbotics has indeed taken over the operations of HVWTech.com! The owner of HVWTech has new priorities in his life (about 1 year old, drooling, and crawling around on the floor), and decided to hand off operations to us. We're […]
It's another Friday and we are back with the product that makes sense - it is metric! It is not measured in twips, poppyseeds, barleycorns, yards, furlongs, or any of this funny stuff. It's your good old straightforward decimals. Metric 2.5mm Hex Nut - 25 Pack $4.00 Metric M2.5 Hex Nut, in packs of 25, […]
Solarbotics has been operating for more than 25 years, bringing electronics know-how and supplies to both the electronics professional and hobbyist. We'll be happy to help you too!
Solarbotics, Ltd. is not responsible for misprints or errors on product prices or information. For more information, please see our Terms and Conditions.
Warning: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Please visit www.P65Warnings.ca.gov for more information. This item was manufactured prior to August 31, 2018.