Solarbotics Raspberry Pi 3 SAFE Assembly...

Dave Hrynkiw
April 25, 2016

The instructions for assembling the Pi v3 and the previous acrylic Pi SAFE are quite similar. The only difference between the models is the location of the LED light pipes, so these Pi3 instructions apply generally to all Pi SAFE versions.

1. Your Parts!

IMG_1378-parts
Step 1: Parts
  • 8 x 4-40 nuts
  • 8 x 4-40 x 3/8" bolts
  • 2 x Clear acrylic light-pipes
  • 4 x Black acrylic spacers
  • 6 x Black acrylic SAFE sides (shown here with brown protective paper already removed)
  • 0 x Raspberry Pi (sorry - not included in the kit!)

2. The Baseplate

IMG_1379-Screws and spacers
Step 2: Baseplate preparation

Find 4 of the 4-40 x 3/8" bolts, and put them through the baseplate, and press the spacers on from the other side. Thee bolts will sort of stay put until you can get the Raspberry Pi on the baseplate. (If adding to a VESA mount, do only 2 diagonal screws)

3. Adding the Raspberry Pi

IMG_1382-Pi_mounted copy
Step 3: Mounting the Pi to the baseplate

Slide the Raspberry Pi onto the bolts. The Pi is designed for metric M3 hardware, but we're still using imperial #4 hardware, which is a smidge bigger. The bolts may need to be screwed through the holes in the Pi.

Add the #4 nuts, and tighten them down.

 4. Adding 3 of the 4 Sides

IMG_1383-mount_sides
Step 4: 3 of the 4 sides to be added to the baseplate

Arrange the sides as shows. The sideplate on the top in this image has the long cutout to accommodate a ribbon cable from the 40-pin expansion port. The front faceplate on the right (with the label engravings face-down) is for the communications side. The sideplate on the bottom has the ports for the power, video, and audio I/O.

Align them all up on the baseplate, and use a pair of 4-40 nuts and bolts to lock them in place.

5. Adding the SD-Card / LightPipe Faceplate

IMG_1385-lightpipes_1
Step 5a: Preparing for lightpipes

Lay the final side faceplate face-down beside the assembly, and pop the clear lightpipe parts out of their holder. It is not necessary to strip the paper off this part.

Sandwich the two lightpipes together, and push them into the lightpipe indicator hole. They will sit a bit loose until the faceplate is attached to the baseplate.

IMG_1388-lightpipes_2
Step 5b: Lightpipe assembly

Carefully assemble this assembly to the baseplate, and finish attaching it with the remaining 4-40 nuts and bolts.

Step 6: Top Plate mounting

Notch the top plate into the slots in the rear faceplate, and gently flex the frontplate out to let the tab snap into place. You're ready to power up, with full access to the indication LEDs on the Pi mainboard via the lightpipes!

IMG_1391-final
Complete!

.

MORE POSTS

October 4, 2001
Push Pogo Pins Update

We've received word that we will be receiving new stock on all our push pogo pins, but they will not be available for order until October 8 or 9th. The order link will be restored when the inventory arrives.

May 10, 2006
Solarbotics SolarSpeeder competition

The Western Canadian Robot Games are close at hand (umm... this weekend!), and in response to popular request, we're cranking up the SolarSpeeder contest again! Ever built a Solarbotics SolarSpeeder? Bring it down to the games, enter at our booth (free!), and we'll run a SolarSpeeder target race. Aim your racer at a 10cm (4") […]

September 22, 2011
RoboMaxx n' New Produxx

Are you on, in, under or around the state of Oregon? Do you have the ability with which to get thineself to Medford, which is located in Oregon, on October the 8th? If you answered 'yes' to most of the above questions, you might want to consider dropping in at RoboMaxx - an event which is […]

October 27, 2004
New Parts Available

We are now stocking the Microchip PIC16F877A microcontroller individually that is used in our K SV-PIC kit. It is a very versatile and powerful chip, and you don't even need to buy 1000 at a crack! As well, we are selling the motor that is straight out of the GM2/3/8/9. Dontcha just hate it when […]

Solarbotics Ltd Logo
Solarbotics has been operating for more than 25 years, bringing electronics know-how and supplies to both the electronics professional and hobbyist. We'll be happy to help you too!

Solarbotics, Ltd. is not responsible for misprints or errors on product prices or information. For more information, please see our Terms and Conditions.

Warning: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Please visit www.P65Warnings.ca.gov for more information. This item was manufactured prior to August 31, 2018.

cart