The instructions for assembling the Pi v3 and the previous acrylic Pi SAFE are quite similar. The only difference between the models is the location of the LED light pipes, so these Pi3 instructions apply generally to all Pi SAFE versions.
1. Your Parts!
8 x 4-40 nuts
8 x 4-40 x 3/8" bolts
2 x Clear acrylic light-pipes
4 x Black acrylic spacers
6 x Black acrylic SAFE sides (shown here with brown protective paper already removed)
0 x Raspberry Pi (sorry - not included in the kit!)
2. The Baseplate
Find 4 of the 4-40 x 3/8" bolts, and put them through the baseplate, and press the spacers on from the other side. Thee bolts will sort of stay put until you can get the Raspberry Pi on the baseplate. (If adding to a VESA mount, do only 2 diagonal screws)
3. Adding the Raspberry Pi
Slide the Raspberry Pi onto the bolts. The Pi is designed for metric M3 hardware, but we're still using imperial #4 hardware, which is a smidge bigger. The bolts may need to be screwed through the holes in the Pi.
Add the #4 nuts, and tighten them down.
4. Adding 3 of the 4 Sides
Arrange the sides as shows. The sideplate on the top in this image has the long cutout to accommodate a ribbon cable from the 40-pin expansion port. The front faceplate on the right (with the label engravings face-down) is for the communications side. The sideplate on the bottom has the ports for the power, video, and audio I/O.
Align them all up on the baseplate, and use a pair of 4-40 nuts and bolts to lock them in place.
5. Adding the SD-Card / LightPipe Faceplate
Lay the final side faceplate face-down beside the assembly, and pop the clear lightpipe parts out of their holder. It is not necessary to strip the paper off this part.
Sandwich the two lightpipes together, and push them into the lightpipe indicator hole. They will sit a bit loose until the faceplate is attached to the baseplate.
Carefully assemble this assembly to the baseplate, and finish attaching it with the remaining 4-40 nuts and bolts.
Step 6: Top Plate mounting
Notch the top plate into the slots in the rear faceplate, and gently flex the frontplate out to let the tab snap into place. You're ready to power up, with full access to the indication LEDs on the Pi mainboard via the lightpipes!
Fun fact: As I type this out, I'm doing so not while sitting at my desk, but sitting on it. I highly recommend you try it. Probably not very ergonomic, but hey. When the boss temporarily commandeers your chair, you gotta make do with what you got. So this week we have a few small […]
Seeed Grove - Digital Light Sensor $9.90 This module is based on the I2C light-to-digital converter TSL2561. Grove - DMX512 $4.90 Interface Grove to DMX512 for control of stage lighting and effects. Grove - Temperature & Humidity Pro Sensor $14.90 For more precise environmental measurements using the Grove system. Grove - Recorder $17.95 Grove record […]
Electronic things come in all shapes and sizes, with all sorts of different appendages. This week we have a few itty-bitty components that have legs/leads. They're like bugs, except made of metal. And, you know, completely inanimate. (Inanimate bugs? Those are the best kind...) LM1084 5V 5A LDO Voltage Regulator $3.94 The LM1084IT-5.0 is a […]
The biggest complaint we've ever had is that the Sumovore is boring. I mean, yeah, it can beat the tar out of most other sumos in the ring without batting an eye. But it's just so boring to watch. It'd be funner to watch the paint dry on a pot of boiling water. So, after […]
Solarbotics has been operating for more than 25 years, bringing electronics know-how and supplies to both the electronics professional and hobbyist. We'll be happy to help you too!
Solarbotics, Ltd. is not responsible for misprints or errors on product prices or information. For more information, please see our Terms and Conditions.
Warning: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Please visit www.P65Warnings.ca.gov for more information. This item was manufactured prior to August 31, 2018.