The instructions for assembling the Pi v3 and the previous acrylic Pi SAFE are quite similar. The only difference between the models is the location of the LED light pipes, so these Pi3 instructions apply generally to all Pi SAFE versions.
1. Your Parts!
8 x 4-40 nuts
8 x 4-40 x 3/8" bolts
2 x Clear acrylic light-pipes
4 x Black acrylic spacers
6 x Black acrylic SAFE sides (shown here with brown protective paper already removed)
0 x Raspberry Pi (sorry - not included in the kit!)
2. The Baseplate
Find 4 of the 4-40 x 3/8" bolts, and put them through the baseplate, and press the spacers on from the other side. Thee bolts will sort of stay put until you can get the Raspberry Pi on the baseplate. (If adding to a VESA mount, do only 2 diagonal screws)
3. Adding the Raspberry Pi
Slide the Raspberry Pi onto the bolts. The Pi is designed for metric M3 hardware, but we're still using imperial #4 hardware, which is a smidge bigger. The bolts may need to be screwed through the holes in the Pi.
Add the #4 nuts, and tighten them down.
4. Adding 3 of the 4 Sides
Arrange the sides as shows. The sideplate on the top in this image has the long cutout to accommodate a ribbon cable from the 40-pin expansion port. The front faceplate on the right (with the label engravings face-down) is for the communications side. The sideplate on the bottom has the ports for the power, video, and audio I/O.
Align them all up on the baseplate, and use a pair of 4-40 nuts and bolts to lock them in place.
5. Adding the SD-Card / LightPipe Faceplate
Lay the final side faceplate face-down beside the assembly, and pop the clear lightpipe parts out of their holder. It is not necessary to strip the paper off this part.
Sandwich the two lightpipes together, and push them into the lightpipe indicator hole. They will sit a bit loose until the faceplate is attached to the baseplate.
Carefully assemble this assembly to the baseplate, and finish attaching it with the remaining 4-40 nuts and bolts.
Step 6: Top Plate mounting
Notch the top plate into the slots in the rear faceplate, and gently flex the frontplate out to let the tab snap into place. You're ready to power up, with full access to the indication LEDs on the Pi mainboard via the lightpipes!
Finally, the freezing temperatures are somewhat over, and the outside seems almost livable, as opposed to run-for-your-life-or-else-you-freeze-able. Our links also, no matter the season, stay well-selected and non life-threatening. Photosynthesis-based Table Table that harvests energy of the sun by Dutch designer Marjan Van Aubel, via Designboom. Visualizing Sorting Algorithms Sorting algorithms are always interesting to […]
Not every product we design is destined to make it to the consumer. Sometimes a great idea gets taken to completion before we realize that one factor or another dooms it to an existence in our failed project bin. One such project that now lives a watery grave is the Sharkbot. Akin to our much […]
Fixed a reset problem in the sumo code, turns out the a If...Then statement does not store its location on the stack. Ergo the return instruction at the bottom of the turn function was pulling a random location. Anyway a change from a return to a goto and everything is shipshape, savvy? Then download the […]
We've churned out another Bicore Experimenter's PCB project: The "Bare Bones PhotoVore". This is an elegant little circuit, which offers the functionality of a basic photovore (with tactiles) all on a very simple circuit. Ours is solar-powered by a Miller Solarengine, but if you wanted to build one with a battery, your parts count would […]
Solarbotics has been operating for more than 25 years, bringing electronics know-how and supplies to both the electronics professional and hobbyist. We'll be happy to help you too!
Solarbotics, Ltd. is not responsible for misprints or errors on product prices or information. For more information, please see our Terms and Conditions.
Warning: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Please visit www.P65Warnings.ca.gov for more information. This item was manufactured prior to August 31, 2018.