The instructions for assembling the Pi v3 and the previous acrylic Pi SAFE are quite similar. The only difference between the models is the location of the LED light pipes, so these Pi3 instructions apply generally to all Pi SAFE versions.
1. Your Parts!
8 x 4-40 nuts
8 x 4-40 x 3/8" bolts
2 x Clear acrylic light-pipes
4 x Black acrylic spacers
6 x Black acrylic SAFE sides (shown here with brown protective paper already removed)
0 x Raspberry Pi (sorry - not included in the kit!)
2. The Baseplate
Find 4 of the 4-40 x 3/8" bolts, and put them through the baseplate, and press the spacers on from the other side. Thee bolts will sort of stay put until you can get the Raspberry Pi on the baseplate. (If adding to a VESA mount, do only 2 diagonal screws)
3. Adding the Raspberry Pi
Slide the Raspberry Pi onto the bolts. The Pi is designed for metric M3 hardware, but we're still using imperial #4 hardware, which is a smidge bigger. The bolts may need to be screwed through the holes in the Pi.
Add the #4 nuts, and tighten them down.
4. Adding 3 of the 4 Sides
Arrange the sides as shows. The sideplate on the top in this image has the long cutout to accommodate a ribbon cable from the 40-pin expansion port. The front faceplate on the right (with the label engravings face-down) is for the communications side. The sideplate on the bottom has the ports for the power, video, and audio I/O.
Align them all up on the baseplate, and use a pair of 4-40 nuts and bolts to lock them in place.
5. Adding the SD-Card / LightPipe Faceplate
Lay the final side faceplate face-down beside the assembly, and pop the clear lightpipe parts out of their holder. It is not necessary to strip the paper off this part.
Sandwich the two lightpipes together, and push them into the lightpipe indicator hole. They will sit a bit loose until the faceplate is attached to the baseplate.
Carefully assemble this assembly to the baseplate, and finish attaching it with the remaining 4-40 nuts and bolts.
Step 6: Top Plate mounting
Notch the top plate into the slots in the rear faceplate, and gently flex the frontplate out to let the tab snap into place. You're ready to power up, with full access to the indication LEDs on the Pi mainboard via the lightpipes!
We are working on fixing the bugs in the website, along with a number of other improvements. Some of you may already know that we are rewriting the ordering portion, making processing your BEAM needs that much easier. It is approaching it's release very quickly, we are just doing the final testing now! So give […]
We're sorry to see Becky go off to work with her husband on their own endevours, but that's ok; we have Robin now - a most worthy replacement. Bye Becky - we'll miss you! Come back sometime and say hi to Robin, ok?
Well folks, we don't have any new products to show off today (I guess we're all too busy watching the Olympics...), but we DO have a small handful of recently uploadedYouTube videos to show off. Dave has been sifting through some of our old archive tapes, and pulled out a few gems, like this footage […]
Simple cosplay cat ears made out of Fosshape, decorated with rhinestones and complete with RGB LEDs for color changing effect. Materials: Fosshape 300 2 x slow scroll RGB LEDs 2 x CR2032 coin cell batteries 2 x coin cell battery holders 100 flatback rhinestones 2 x hairclips fake fur steel ball chain Tools: scissors heat […]
Solarbotics has been operating for more than 25 years, bringing electronics know-how and supplies to both the electronics professional and hobbyist. We'll be happy to help you too!
Solarbotics, Ltd. is not responsible for misprints or errors on product prices or information. For more information, please see our Terms and Conditions.
Warning: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Please visit www.P65Warnings.ca.gov for more information. This item was manufactured prior to August 31, 2018.