If you are in Calgary & area this weekend, come see us at BMO Centre Expo Holiday Market. On November 25 & 26, 2017 we are going to be at booth 1314 with our new and all-time favorite gadgets. The hours of the show are: Saturday 10-6, Sunday 10-5.
The instructions for assembling the Pi v3 and the previous acrylic Pi SAFE are quite similar. The only difference between the models is the location of the LED light pipes, so these Pi3 instructions apply generally to all Pi SAFE versions.
Find 4 of the 4-40 x 3/8" bolts, and put them through the baseplate, and press the spacers on from the other side. Thee bolts will sort of stay put until you can get the Raspberry Pi on the baseplate. (If adding to a VESA mount, do only 2 diagonal screws)
Slide the Raspberry Pi onto the bolts. The Pi is designed for metric M3 hardware, but we're still using imperial #4 hardware, which is a smidge bigger. The bolts may need to be screwed through the holes in the Pi.
Add the #4 nuts, and tighten them down.
Arrange the sides as shows. The sideplate on the top in this image has the long cutout to accommodate a ribbon cable from the 40-pin expansion port. The front faceplate on the right (with the label engravings face-down) is for the communications side. The sideplate on the bottom has the ports for the power, video, and audio I/O.
Align them all up on the baseplate, and use a pair of 4-40 nuts and bolts to lock them in place.
Lay the final side faceplate face-down beside the assembly, and pop the clear lightpipe parts out of their holder. It is not necessary to strip the paper off this part.
Sandwich the two lightpipes together, and push them into the lightpipe indicator hole. They will sit a bit loose until the faceplate is attached to the baseplate.
Carefully assemble this assembly to the baseplate, and finish attaching it with the remaining 4-40 nuts and bolts.
Notch the top plate into the slots in the rear faceplate, and gently flex the frontplate out to let the tab snap into place. You're ready to power up, with full access to the indication LEDs on the Pi mainboard via the lightpipes!
.
If you are in Calgary & area this weekend, come see us at BMO Centre Expo Holiday Market. On November 25 & 26, 2017 we are going to be at booth 1314 with our new and all-time favorite gadgets. The hours of the show are: Saturday 10-6, Sunday 10-5.
Being April in Calgary, it should come as no surprise to any of you that yesterday we had a lovely blizzard which melted and froze, coating everything in a delicious layer of ice. This, of course, is somehow connected to the fact that Solarbotics El Presidante, Dave, is currently in Las Vegas where it is […]
Solarbotics / Active-Tech Calgary Store Sale! Although we have a new website, we're still working on bringing over the inventory from Active-Tech into it. In the meanwhile, we're participating in the Active-Tech sale, with additional items from Solarbotics Ltd. Solarbotics_Active_Calgary_December_2019_Sale and come on by our store to take advantage of it until January 5 […]
Unlike Sparkfun, who actually manage to find fake Atmel ICs, we just get strange batches. The Atmel ATMega328 is the power behind the Arduino/Freeduino/*duino, and we have to set up a programming system to burn the venerable Arduino Bootloader into these chips. We normally use an AVR STK500 in HVSP (high voltage serial programming) mode, […]
Solarbotics, Ltd. is not responsible for misprints or errors on product prices or information. For more information, please see our Terms and Conditions.
Warning: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Please visit www.P65Warnings.ca.gov for more information. This item was manufactured prior to August 31, 2018.