Solarbotics Raspberry Pi 3 SAFE Assembly...

Dave Hrynkiw
April 25, 2016

The instructions for assembling the Pi v3 and the previous acrylic Pi SAFE are quite similar. The only difference between the models is the location of the LED light pipes, so these Pi3 instructions apply generally to all Pi SAFE versions.

1. Your Parts!

IMG_1378-parts
Step 1: Parts
  • 8 x 4-40 nuts
  • 8 x 4-40 x 3/8" bolts
  • 2 x Clear acrylic light-pipes
  • 4 x Black acrylic spacers
  • 6 x Black acrylic SAFE sides (shown here with brown protective paper already removed)
  • 0 x Raspberry Pi (sorry - not included in the kit!)

2. The Baseplate

IMG_1379-Screws and spacers
Step 2: Baseplate preparation

Find 4 of the 4-40 x 3/8" bolts, and put them through the baseplate, and press the spacers on from the other side. Thee bolts will sort of stay put until you can get the Raspberry Pi on the baseplate. (If adding to a VESA mount, do only 2 diagonal screws)

3. Adding the Raspberry Pi

IMG_1382-Pi_mounted copy
Step 3: Mounting the Pi to the baseplate

Slide the Raspberry Pi onto the bolts. The Pi is designed for metric M3 hardware, but we're still using imperial #4 hardware, which is a smidge bigger. The bolts may need to be screwed through the holes in the Pi.

Add the #4 nuts, and tighten them down.

 4. Adding 3 of the 4 Sides

IMG_1383-mount_sides
Step 4: 3 of the 4 sides to be added to the baseplate

Arrange the sides as shows. The sideplate on the top in this image has the long cutout to accommodate a ribbon cable from the 40-pin expansion port. The front faceplate on the right (with the label engravings face-down) is for the communications side. The sideplate on the bottom has the ports for the power, video, and audio I/O.

Align them all up on the baseplate, and use a pair of 4-40 nuts and bolts to lock them in place.

5. Adding the SD-Card / LightPipe Faceplate

IMG_1385-lightpipes_1
Step 5a: Preparing for lightpipes

Lay the final side faceplate face-down beside the assembly, and pop the clear lightpipe parts out of their holder. It is not necessary to strip the paper off this part.

Sandwich the two lightpipes together, and push them into the lightpipe indicator hole. They will sit a bit loose until the faceplate is attached to the baseplate.

IMG_1388-lightpipes_2
Step 5b: Lightpipe assembly

Carefully assemble this assembly to the baseplate, and finish attaching it with the remaining 4-40 nuts and bolts.

Step 6: Top Plate mounting

Notch the top plate into the slots in the rear faceplate, and gently flex the frontplate out to let the tab snap into place. You're ready to power up, with full access to the indication LEDs on the Pi mainboard via the lightpipes!

IMG_1391-final
Complete!

.

MORE POSTS

December 9, 2004
Harold's "Tank"

Harold Ilano built this SW2.2 / VBug inspired 5 motor walker named "Tank", and just recently announced it on the BEAM mailing list. It's a very effective and quick device - nicely done, and well worth a look-see. It still impresses me what we can do without a microcontroller...

February 16, 2016
OpenBeam & Nightmares in China Sour...

We've been a big fan of Openbeam for a long time, and when Terence Tam started producing 3D printers using this material, we were hopeful that this would be a great fit for his operation. Nice material, great engineering - what could go wrong? LOTS. Follow his spiral down the Asian rabbit-hole when his selected […]

May 30, 2012
Cool Links Wednesday: Interactive Painti...

Bleh. It's the middle of the week. Two-and-a-half days down, and two-and-a-half more to go. For a little bit of inspiration (and a bit of distraction), check out this week's round of neat-o links from around the office: The Stream : The future of drone technology This YouTube video features some interesting discussion about Drones […]

March 25, 2004
Solarbotics Antweight

Adam Conus sent us a nice little message about his antweight combat robot The Fly.: Western Allied Robotics is kicking off another year of antweight combat events and I need new motors. (Because I'm very, very hard on them!) Still, they're cheap and light. Check out- http://home.comcast.net/~conusa/adam.htm to see the robot complete with solarbotics sticker!

1 13 14 15 16 17 253
Solarbotics Ltd Logo
Solarbotics has been operating for more than 25 years, bringing electronics know-how and supplies to both the electronics professional and hobbyist. We'll be happy to help you too!

Solarbotics, Ltd. is not responsible for misprints or errors on product prices or information. For more information, please see our Terms and Conditions.

Warning: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Please visit www.P65Warnings.ca.gov for more information. This item was manufactured prior to August 31, 2018.

cart