After a long hiatus, our PP3 chisel-tip pogo pins are back! And it looks like they're here to stay, so no more drop-outs in supply. I know that we use them for robotics applications, but there's a lot of people using them for other electronics purposes. Now you can get them reliably, and in quantity, […]
APA102-2020 MicroNova Custom LED Choker
Solarbotics Ltd
February 23, 2018
I created this choker as a project to demonstrate the new MicroNova APA102-2020 LED strips.
Photo by Yeti, edited by Batgirl
These addressable LEDs are extremely small, less than 1/4 the size of a standard 5050 LED.
This project was built using engineering sample standard MicroNova 99 LED / meter strips . The MicroNova strips we are selling have 198/meter - twice the density!
Reason for a Choker necklace:
Hats have been done, shoes have been done, pendants have been done. This is something new for a Valentine’s dance costume, so I decided to go with a choker design. I also wanted something that was interactive, something that would add another layer of WOW to just lighting.
The Build:
I used a Wemos D1 Mini development board along with a boost-converting battery shield for the Wemos D1.
The battery shield was a particularly good choice here because the MicroNova LEDs should be supplied a solid 5VDC. This board boosts the battery voltage to 5V, and then the Wemos D1 Mini bucks it down to 3V3 for it's own operation.
A mini SPDT Slide switch toggles the power from the battery shield to the D1. This allows charging the battery using the battery shield USB connector while not powering the D1.
Epoxy locks the switch and wires in place.
The battery used is a conveniently handy older 450mAh Lithium Polymer. Depending on the lighting mode, this battery can power the necklace for a couple of hours.
I used elastic thread to attach the LED strip and components to the necklace. A heavy duty needle was all that was needed to punch through the (imitation) leather belt. Because the thread was elastic and tied under tension, it held the MicroNova strip well in place.
Operation:
When the choker powers up, it creates a WiFi Access Point called "HeartBurnChoker1".
Once I connected to this WiFi, I opened a browser and went to 192.168.4.1. The control interface is simple, but effective. The D1 Mini has more than ample power and speed to effectively drive these LEDs. The MicroNova features separate clock & data lines, so even relatively slow I/O (like Raspberry Pi) can still make it work.
Video of the Collar in Action
MORE POSTS
The Marble Machine at Solarbotics
Aaaand this is a quick note to remind everyone that the Solar Marble Machine is now fully available for purchase from our website. Enjoy!
Friday New Product and a Little Bit of F...
Solarbotics is helping out local fashion designers prepare their e-wearables for the Calgary MakeFashion. This time, Tony Grimes dropped in to experiment with his fiber-optic cloth from SensingTex as an illuminating surface, but the included 5mm LED was not dazzling enough. Time to hack in our 3W RGB Star Controller! The plan was to shift […]
Oomlout - Solarbotics Edition!
Good news, good news! We've been following the Oomlout system of learning Arduino since last February, and we've finally finished putting together our own Solarbotics Edition of the open-source ARDX Arduino Experimenter's Kit. Besides just working with the fine folks at Oomlout to make sure our edition meets their high standards, we've also been contributing […]
Solarbotics has been operating for more than 25 years, bringing electronics know-how and supplies to both the electronics professional and hobbyist. We'll be happy to help you too!
Solarbotics, Ltd. is not responsible for misprints or errors on product prices or information. For more information, please see our Terms and Conditions.
Warning: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Please visit www.P65Warnings.ca.gov for more information. This item was manufactured prior to August 31, 2018.