Wio Node SKU: 30314
Wio Node
$11.50 USD
An small ESP8266 based SoC with full Grove Support, LiPo Support, and a mature API
In stock
Description
The new Wio Node was born with most of the features of its elder brother:
- An ESP8266 based open-source Wi-Fi development board
- Supports Plug-n-Play Groves
- Visual Configuration
- OTA (Over-The-Air) Firmware Updates
- RESTful APIs
- IFTTT Application
- Android & iOS APPs
This little guy is cheaper, smaller and lighter in weight.
Even though the compact design only has two Grove connectors, it still offers as many as 2 Digital I/O, 1 Analog Input, 1 UART and 2 I2C interfaces to communicate with up to 42 (and more to come) Grove modules. Setting up an IoT device with Wio Node is piece of cake as all the Grove sensor/actuator modules can be visually configured to RESTful APIs on your mobile APPs, and the physical circuit connections does not involve any bread boarding, soldering, or wire jumpers. Once you finish updating the firmware over-the-air (OTA), you’ll find out it only takes you 5 minutes to build an IoT application with the Wio Node.
Owing to its low-cost, easy-to-use and compact design, Wio Node can be used to build an IoT system where a large amount of ‘things’ are required to be connected to the internet. Seeed has provided detailed instructions and rich tutorials at http://iot.seeed.cc/ to help you getting started with your Wio Node easily and quickly. You can also find out more interesting stuff at the Wio Community, where all the Wio fans gather to share their ideas and experiences.
Features:
- Cheaper, lighter, smaller, and simpler
- Built around ESP 8266 Wifi module
- Supports Plug-n-Play Groves
- Visual Configuration
- OTA (Over-The-Air) Firmware Updates
- RESTful APIs
- IFTTT Application
- Android & iOS APPs
Specifications:
- Wi-Fi Network Protocol: 802.11b/g/n
- Wi-Fi Encryption Technologies: WEP/TKIP/AES
- Expansion (2x Grove Connectors): UART0/I2C0/D0, Analog/I2C1/D1
- Input Voltage:
- Battery holder: 3.0~4.2V
- Micro USB: 5V
- Operating Voltage: 3V3
- Maximum Charge Current: 500mA
- Digital I/O Pins: 4
- Analog Input Pins:1
- DC Current PER I/O PIN: 12mA
- Flash Memory: 4MByte (W25Q32B)
- Frequency of Crystal: 26MHz
- Dimensions: 28mm x 28mm
More Info
Weight | 0.0107 kg |
---|---|
Dimensions | 6 × 4.5 × 2 cm |
Ecosystem |
Only logged in customers who have purchased this product may leave a review.
Related products
-
Push Pogo Pin – Cone Tip
SKU: PP12-100This 33mm (1.3") long cone tipped pogo pin probe is normally used for electronic JTAG uses, but we use them for bots!$1.25 USDIn stock
Add to cart -
Push Pogo Pin 4 – Cup Tip
SKU: PP4This 33mm (1.3") long cup-tipped pogo pin probe pin is normally used for electronic JTAG uses, but we use them for bots!$1.25 USDIn stock
Add to cart -
Magnet
SKU: Mag1These 3/4" Neodymium magnets are very strong. Useful for all kinds of Magbot experiments or just holding posters up on metal surfaces as we like to do!$2.75 USDOut of stock
Read more -
2mm White Sintra
SKU: SIN2mm-WThis 2mm thick 8x12" expanded PVC sheet has excellent robot-building characteristics.$2.85 USDIn stock
Add to cart -
AXE Stack-28 Kit
SKU: 28580The PICAXE is great, but on a breadboard, you'll like it even better. Many handy features make the AXE Stack more useful than just plugging your PICAXE into a breadboard!$21.95 USDIn stock
Add to cart
Reviews
There are no reviews yet.