Connectors


Show: Items

Sort By:


105 Products Found


BattR15

Lithium Polymer Battery - 2000mAh (Lipo)

These are very slim, extremely light weight batteries based on the new Polymer Lithium Ion chemistry.

$12.95 USD

FPin5LP

Female Low Profile Socket Strip - 5 per

Female Low profile socket strip - 5 per Strip, 0.100" (2.54mm) spacing

$0.45 USD

MPin2

Male Strip Pins - 2 per

Based on 0.1" spacing, this 2-pin header spacing is a very popular way to interface sensors & accessories to your design. Ground / Voltage / Signal!

$0.23 USD

MPin8L-235

Male Strip Pins - 8 per, 2.54mm

2.54mm pitch 8 pin Male header with long 23.5mm pins

$0.40 USD

TBLK3-100

3 Position Terminal block .1" (2.54mm) spacing

It's a SMALL terminal block, designed to mount in standard 0.1" (0.254mm) spaced holes. Ideal for permanent yet serviceable connections to microcontrollers.

$1.63 USD

Mpin6

Male Strip Pins - 6 per

Male Strip - 6 per Strip, gold flash surface on 0.1" spacing

$0.30 USD

MPin6RA

Male Strip Pins - 6 per (Right Angle)

Male Strip - 6 per Strip, gold flash surface on 0.1" spacing. These are bent over at 90 degrees for edge-wise connections.

$0.35 USD

TBLK2

2 Position Terminal Block

2-position, stackable terminal blocks - they're not just for wires anymore! (We use them for sensor mounts now...)

$1.00 USD

TBLK3

3 Position Terminal Block

Three Position Terminal block is good for mounting heavy wire to circuit boards, like for motor and battery connections.

$1.10 USD

PP1

Push Pogo Pin 1 - Masher

This 33mm (1.3") long masher-tipped pogo/probe ping is normally used for electronic JTAG uses, but we use them for bots!

$1.25 USD

PP3

Push Pogo Pin 3 - Chisel Point

This 33mm (1.3") long poker-tipped pogo pin probe is normally used for electronic JTAG uses, but we use them for bots!

$1.25 USD

PP4

Push Pogo Pin 4 - Cup Tip

This 33mm (1.3") long cup-tipped pogo pin probe pin is normally used for electronic JTAG uses, but we use them for bots!

$1.25 USD

PP6

Push Pogo Pin 6 - 6 Point

This 33mm (1.3") long 6-groove tipped pogo pin probe is normally used for electronic JTAG uses, but we used them for bots!

$1.25 USD

PP8

Push Pogo Pin 8 - Round End

This 33mm (1.3") long round-tipped pogo pin probe is normally used for electronic JTAG uses, but we use them for bots!

$1.25 USD

PPH1

Push Pogo Probe Holder

This holder is specially designed for easy installation/replacement of the PP1/3/4/6/8 Pogo Pins

$1.25 USD

PPH-40

Push Pogo Probe Holder - Style 40 size

This is the holder for our now discontinued PP8S short pogo pins.

$1.50 USD

APin

Spare Part - Long Socket Pin

Long Augut Socket pins for sensors, rocker points, or anything else you can think of!

$0.30 USD

DC-8 Pin

8 Pin DIP Socket Carrier

The idea of a DIP socket is to allow easy insertion/replacement of chips in existing circuits.

$0.25 USD

DC-14 Pin

14 Pin DIP Socket Carrier

14 Pin DIP Socket, good for use with the 74AC14, 74HCT4066, LM324 and other similar foot-print ICs.

$0.30 USD

DC-16 Pin

16 Pin DIP Socket Carrier

16 Pin DIP Socket Carrier - great for piece-of-mind with sensitive IC installations!

$0.30 USD

DC-20 Pin

20 Pin DIP Socket Carrier

20 pin DIP carriers are great for free-form 74xx240/245 circuit layouts.

$0.35 USD

DC-28 Pin

28 Pin DIP Socket Carrier

28 pin DIP carrier for the ATmega8L or other 28 pin DIP devices.

$0.50 USD

DC-40W Pin

0.600" wide 40 Pin DIP Socket Carrier

A chip carrier for the 16F877A or other 40 pin DIP device.

$0.75 USD

SPin30

30 Pin SIP Sockets

These strip headers are snappable, so you can 'snik' off exactly how many you need.

$2.50 USD

DC-24W Pin

24 Pin Wide DIP Socket Carrier

24 pins on 0.6" spacing - ideal for BS2 mounting!

$0.50 USD

PP12-100

Push Pogo Pin - Cone Tip

This 33mm (1.3") long cone tipped pogo pin probe is normally used for electronic JTAG uses, but we use them for bots!

$1.25 USD

PP2-50

50-Series Push Pogo Pin - 4-Sided Point

This smaller, 16.4mm long cone-tipped pogo/probe ping is normally used for electronic JTAG uses, but we use them for bots!

$1.50 USD

PP2-75

75-Series Push Pogo Pin - 4 Point

This medium 17mm long 4-sided point tipped pogo pin probe is normally used for electronic JTAG uses, but we use them for bots!

$1.25 USD

PPH-50

50-Series Push Pogo Probe Holder

This little devices allow you to simply and easily install and replace existing 50-series pogo pins

$1.50 USD

Fpin4

Female Strip Socket - 4 per strip

Female Socket Strip - 4 per Strip, gold flash surface, 0.1" spacing

$0.50 USD

DC-18 Pin

18-Pin DIP Socket Carrier

The idea of a DIP socket is to allow easy insertion/replacement of chips in existing circuits.

$0.25 USD

17440

Barrel Power Jack socket, 2.1mm Connection

2.1mm barrel power jack socket. For connecting barrels, I mean "power leads"!

$1.00 USD

14052

I2C-It Y-Cable Harness set

The I2C-It is a great sensor, and is only more so when used as part of a greater chain. Use the I2C-It Cable harness and pin set to set up multiple sensors!

$2.84 USD

14150

Phidgets Sensor Cable 60

Use this 60cm/24" sensor cable to plug in your Phidgets sensor to the Interface Kit 8/8/8.

$2.05 USD

15032

SparkFun Barrel Jack Power Switch - M-F

Instead of yanking and plugging 2.1" power connectors, toggle the power with this short inline power switch.

$2.50 USD

15009

12" Servo Extension Cable - Male / Female

Universal connectors fit both Futaba and Hi-Tec/JR(S). Male to female. Very flexible, 12" long 22 AWG stranded wire. Black, red, white silicone rubber insulation.

$3.99 USD

15005

14" 3-Conductor Extension Cable

The 14" 3-conductor extension cable is ideal for use with additional accessories mating with the Prop-1 and Prop-2 controllers

$2.50 USD

15010

24" Servo Extension Cable - Male / Female

Universal connectors fit both Futaba and Hi-Tec/JR(S). Male to female. Very flexible, 24" long 22 AWG stranded wire. Black, red, white silicone rubber insulation.

$4.99 USD

15011

36" Servo Extension Cable - Male / Female

Universal connectors fit both Futaba and Hi-Tec/JR(S). Male to female. Very flexible, 36" long 22 AWG stranded wire. Black, red, white silicone rubber insulation.

$5.99 USD

14180

7.5" Battery wire - JST with Black / Red

JST connectors are tight & tidy, but not that easy to plug into, unless if you have some of these!

$0.95 USD

14130

HighSpeed Encoder Cable

Looking for a HighSpeed Encoder Cable ? Get your HighSpeed Encoder Cable online now!

$5.25 USD

14050

I2C-It Y-Cable Harness

The I2C-It is a great sensor, and is only more so when used as part of a greater chain. Use the I2C-It Cable harness to hook them up!

$2.50 USD

14160

Sensor Cable 350

The Phidgets Sensor Cable 350 is used for the analog input on the Phidget Interface Kit 8/8/8.

$2.99 USD

1810

USB type B Connector

USB type-B connectors are the big ugly square ones. Easy to find cables for, but they sure ain't very pretty. So they still have value. Get them here at Solarbotics!

$1.29 USD

42050

28-Pin ZIF Socket 0.3" Wide

This is a high-quality, easy to use 28 pin ZIF socket that is 0.3" wide.

$2.95 USD

20190

8-Pin and 14-Pin N-SOIC Adapter

The 8-Pin and 14-Pin N-SOIC Adapter gives you the ability to program 8 & 14-pin N-SOIC package PICmicros.

$10.99 USD

17560

Socket 28-Pin Wide DIP

This socket will seat any 28-pin wide dip IC.

$0.25 USD

MPin3-Lock

3-Pin Header with Locking Shroud

3-pin headers are used with MANY accessories, and some even use "lock tab" or "buckled" connectors that physically lock them into place. Here's a socket that mates with them!

$0.35 USD

MPin36

36-Pin Male Snappable Header Strip

Sometimes...you just need pins. Lots of pins. Not sure how long, but lots. So here's a strip of 36 that's a convenient size to 'snik' apart to whatever length you need!

$2.40 USD

MMPin40

40-Pin Machine Socket Snappable Header Strip

This is a very large row of high quality machine pin headers - break to fit.

$2.95 USD

Currency


Login

Email:

Password:

Remember Me

Forgot Your Password?

Don't Have an Account?
Sign Up!