Prototyping


Show: Items

Sort By:


326 Products Found


50840

Li-Ion/Polymer Battery Charger/Balancer - 80W, 6A

The iMax B6 Balance Charger accurately balances and charges Lithium Polymer, LiFe (A123), NiCd and NiMH batteries. The B6 will balance charge LiPo/LiFe up to 6S and NiMH/NiCd up to 15S and shows individual cell voltage during charge with realtime updates throughout the charge cycle.

$32.95 USD

TBLK2-137

2 Position Terminal Block 0.137 Spacing

Want to lock down heavier gauge wires down semi-permanent fashion? Here's a 2-position terminal block with 0.137" (3.5mm) spacing.

$1.25 USD

TBLK3-137

3 Position Terminal Block

Want to lock down heavier gauge wires down semi-permanent fashion? Here's a 3-position terminal block with 0.3"0 (3.5mm) spacing.

$1.22 USD

TBLK6-137

6 Position Terminal Block 0.137 Spacing

Want to lock down heavier gauge wires down semi-permanent fashion? Here's a smallish terminal block with 0.137" (3.5mm) spacing.

$1.49 USD

TBLK8-137

8 Position Terminal Block 0.137 Spacing

Want to lock down heavier gauge wires down semi-permanent fashion? Here's a 8-position terminal block with 0.137" (3.5mm) spacing.

$1.67 USD

52620

Steel Linear Rail, 40cm (15.75") length

For moving things in a straight, STRAIGHT line, you need linear rails!

$50.00 USD

17442

2.1mm DC Power Plug Short

Yup... It's a DC power plug jack. Exciting stuff.

$1.75 USD

BattC2032

CR2032 3V Lithium Coincell Battery

Here's a common light weight 2032 coincell battery. Great for powering tiny robots, real time clocks and LED throwies!

$1.20 USD

BHold2032

CR2025/CR2032 Coincell Battery Holder

Here's a coin cell holder for mounting the most common types of coin cell batteries: CR2032 and CR2025. You could try other batteries but we're guessing you won't have much luck with 'AA's.

$0.49 USD

45075

Sharp Sensor Cable, 20cm

You'll save tons of time and won't need the soldering iron for these Sharp infrared sensor cables! These cables allow you to easily interface Sharp infrared sensors to your robotics project without the need for soldering.

$1.95 USD

14183

JST-PH-2.0 2-Pin Connector Plug w/ Wire

A dramatic tale of two wires. One red. One black. Joined by a single female JST connector. Of destiny.

$1.29 USD

14185

JST-GH-1.25mm 3-Pin Wired Header w/ Plug

The really tiny connectors (not to be confused with the just tiny connectors) that are used on many... tiny things. You'll know them when you see them!

$1.49 USD

50880

Polymer Lithium Ion Battery - 2200mAh 7.4v

This high discharge LiPo is a great way to power any R/C, robotic, or portable project. This is an excellent choice for anything that requires a small battery with a lot of punch.

$15.95 USD

14420

40T GT2 8mm bore Timing Pulley

40 Tooth 8mm Bore Pinion Pulley.

$9.95 USD

FPin2

Female Strip Socket - 2 per Strip

Female Socket Strip - 2 per Strip, 0.1" spacing

$0.20 USD

FPin20

Female Strip Socket - 20 per strip

Single row of 20-holes, female header, 0.1" spacing.

$1.85 USD

52625

OpenBeam T Joining Plate - 2 Pack

T-shaped joining plates for all your OpenBeam creations!

$2.20 USD

52630

OpenBeam L Joining Plate - 2 Pack

L-shaped joining plates for all your OpenBeam creations! This one handily supports 45 & 90 angles.

$2.20 USD

52635

OpenBeam M3 Nuts - 100 Pack

100 pack of M3 nuts for use with OpenBeam.

$3.00 USD

52640

OpenBeam Button Head Socket Cap bolts/screws - 100 Pack

100 pack of button head socket cap screws for use with OpenBeam.

$7.00 USD

52645

OpenBeam Feet - 2 Pack

Feet to fit OpenBeam extrusions, keep your desk scratch free!

$2.20 USD

52650

OpenBeam Servo Bracket

OpenBeam's servo bracket allows you to use just about any standard size servo with your OpenBeam or MicroRAX projects.

$5.20 USD

52655

OpenBeam NEMA17 Stepper Motor Bracket

NEMA17 Stepper Motor Mounts for the OpenBeam construction system.

$7.50 USD

52660

OpenBeam Shaft Clamp Kit

The OpenBeam Shaft Clamp Kit allows you to clamp shafts anywhere on your OpenBeam project.

$8.00 USD

52665

OpenBeam 608 Bearing to NEMA17 Adapter

OpenBeam's adapter to use a 608 skate bearing with NEMA17 mounts.

$4.00 USD

44226

OpenBeam 2mm Hex Key

2mm Hex key for use with the OpenBeam and other metric fastener systems

$4.00 USD

44221

OpenBeam 2mm Flat End Hex Driver

2mm flat end hex driver, ideal for use with OpenBeam.

$4.00 USD

44222

OpenBeam 2mm Ball-End Hex Driver

2mm ball tip hex driver for use with OpenBeam.

$5.50 USD

44224

OpenBeam 5.5mm Hex Nut Driver

5.5mm hex nut driver for use with the OpenBeam system.

$13.00 USD

Mpin14

Male 14-pin Headers

With electronics, there's connections, which usually means sockets and pins.

$0.99 USD

Mpin5LP

Male Strip Pins - 5 per Strip

Male Strip - 5 per Strip, 0.1" spacing

$0.60 USD

15022

4-pin JST SM Plug & Cable Assembly

These 4-pin JST SM pigtail connectors mate perfectly with the RGB LED strips. They also make a good general purpose connector for any project. Each pack comes with one male and one female connector. The wire leads are 6 inches long and are term

$1.50 USD

52690

OpenBeam Precut Kit

If you find it annoying to cut the 1m open beam extrusions down to size - you can now rejoice! Open beam precut lengths are here! Offered in a conveniently packaged kit, these precut pieces are ideal for designing all kinds of interesting structures.

$149.95 USD

52601

OpenBeam Extrusion 30mm Length

This is the 'beam' part of 'Open Beam', the central building component for the system.

$1.00 USD

52602

OpenBeam Extrusion 45mm Length

This is the 'beam' part of 'Open Beam', the central building component for the system.

$1.00 USD

52603

OpenBeam Extrusion 60mm Length

This is the 'beam' part of 'Open Beam', the central building component for the system.

$1.25 USD

52604

OpenBeam Extrusion 90mm Length

This is the 'beam' part of 'Open Beam', the central building component for the system.

$1.50 USD

52605

OpenBeam Extrusion 120mm Length

This is the 'beam' part of 'Open Beam', the central building component for the system.

$1.80 USD

52606

OpenBeam Extrusion 150mm Length

This is the 'beam' part of 'Open Beam', the central building component for the system.

$2.10 USD

52608

OpenBeam Extrusion 210mm Length

This is the 'beam' part of 'Open Beam', the central building component for the system.

$2.75 USD

52610

OpenBeam Extrusion 270mm Length

This is the 'beam' part of 'Open Beam', the central building component for the system.

$3.30 USD

52611

OpenBeam Extrusion 300mm Length

This is the 'beam' part of 'Open Beam', the central building component for the system.

$3.65 USD

BHold9V-Barrel

9V Snap to 2.1mm Barrel Plug Cable

Need a battery for your Arduino that is high enough to regulate the voltage to down to a solid 5V? Well here comes the 9V Snap to 2.1mm Barrel Plug Cable to your rescue! It allows you to plug in 9V and 7.2V rechargeable batteries to anything with a 2.1mm Barrel jack on it.

$2.95 USD

52691

OpenBeam Machinist Precut Kit

Not only does this kit contain the same parts as the OpenBeam Precut Kit 1, it also includes motor mounts and other parts needed for building desktop CNC & 3D machines.

$199.95 USD

52692

OpenBeam Starter Kit - Small

If you find it annoying to cut the 1m OpenBeam extrusions down to size - you can now rejoice! Open beam precut lengths are here! Offered in a conveniently packaged kit, these precut pieces are ideal for designing all kinds of interesting structures.

$79.95 USD

20902

SB400 76 x 48mm, Half-sized Solder Breadboard

This half-sized solder protoboard features power rails arranged on the edges, as you'd find on a standard prototyping board.

$4.99 USD

20904

SB404 95 x 47mm, Half-sized Solder Breadboard

Want to move quickly from prototype to permanent project? Transfer your half-size breadboarded circuit to this convenient breadboard compatible protoboard (with mounting holes & silkscreening) to create a rugged long-lasting prototype! This version has internal and external power rails

$5.50 USD

20906

SB830 164x47mm, Full-sized Solder BreadBoard

This prototyping circuit board matches a regular 1-panel PC breadboard, with handy top-print overlay, and thinner interconnections for friendly track cutting.

$6.50 USD

20908

SB1660 184x93mm, Double-wide Solder Protoboard

Double-wide prototyping space for those particularly large projects.

$12.00 USD

20910

BR1 Solderable PC BreadBoard (single-panel compatible)

This bare solder protoboard matches a regular 1-panel PC breadboard, with outside-edge power rails.

$6.50 USD

Currency


Login

Email:

Password:

Remember Me

Forgot Your Password?

Don't Have an Account?
Sign Up!